Antique Ford Tractor - Ford 671 Select-O-Speed

Parts for Old Tractors
Click Here or call 800-853-2651

TRACTOR PARTS	TRACTOR MANUALS

Antique Ford Tractor: Ford 671 Select-O-Speed
[Return to the Shed]

This model of the 601 series tractors had a Select-O-Speed power-shift transmission which provided ten forward speeds and two reverse speeds. Note - Whenever you see a "7" as the second digit in the Ford "Hundred Series" tractors, it indicates that it has a Select-O-Speed transmission.
Ford 671 Select-O-Speed Tractor

Do you have any comments or questions about this tractor? Ever use one? Know anyone who owned one? If so, please join in on the discussion below. Use the form for entering your comments.

Comments on this Tractor

Johnnie Groce wrote on Thursday, August 25, 2022 (PDT):

Looking for 671 ford tractor 1959 model

Johnnie Groce wrote on Thursday, August 25, 2022 (PDT):

Looking for 671 ford tractor 1959 model

gregg surma wrote on Monday, July 01, 2013 (PDT):

I have a 671 sos and cannot activate the pto will not pull out and cable is not froze up and all transmission speeds are working. Can you tell me what may be the problem, Thanks

paul wrote on Saturday, March 09, 2013 (PST):

i have a ford 4000 mid sixtys i think selectospeed had work done on tractor and ran fine for a while now when inching pedal is released it will not go in gear but will go in and out of gear when move pedal in and out several times any help would be appreciated thanks paul

John Otruba wrote on Sunday, July 29, 2012 (PDT):

I was recently given a ford 871 w/sos trans. havent tried to start it yet. but i need to know how to get it in to neutral without it running so i can pull it onto my trailer if i cant get it running. please help

joe wrote on Wednesday, April 13, 2011 (PDT):

I recently got a 801 with sos, the tractor has a short delay when shifted into gear before it will move. I m unable to locate where to check the fluid level, or the fill. I was told the level/filler was in front of my right foot when sitting on the tractor, however all I see there is a slotted shaft with a lock nut.. need some some help folks.

Daryl Hahm wrote on Tuesday, November 30, 2010 (PST):

cable fix on this tractor for select o shift.. I like a few have found this cable hard to find at best. the cable usualy brakes at the junction. well burn off both ends with a torch careful not to burn off cable. fit both ends in a vice and begin to braze with very low heat I mean real low dont rush work brass into 3/8 inch of the cable on both sides of junction. this is one time you add far more then you need. after you have admired your worst braze job get your file a beverage and some working music. I filed both sides and center area down until I was at the steel cable. once you have filed the repair area down to fit the guide tube make sure tube is streight lube and slide the cable back into the tube. put your tractor back together and go to work. for those who say this cant be done your are welcome to check mine out as this is now the strongest part of my shift system. Do avoid any bends at the base end of the guide tube as your repair isnt flexable.

Greg price wrote on Sunday, November 21, 2010 (PST):

I have a 4040 Industrial with sos trans - I found screen filter at bottom of trans does anyone know where another filter might be hiding Trans doesnt work in higher ranges and reverse until really warmed up - any Ideas

Greg wrote on Sunday, November 21, 2010 (PST):

Ray Wheeler wrote on Thursday, September 09, 2010 (PDT):

I recenly purchased a 1961 761 speed-o-matic Ford tractor. The original paint color was yellow. It was painted over with grey and red. Any information on this tractor would be really helpful. Please email me at Wheelersplace at comcast.net. Thanks!

Demon wrote on Friday, July 23, 2010 (PDT):

i have a ford 3000 with the sos transmission good tractor i need shifter parts having trouble finding them. or a complete shifter.

kelly boyle wrote on Saturday, May 29, 2010 (PDT):

I own a Ford 671 select o speed, it is a very reliable tractor and in excellent condition. I no longer have use for anymore, and I m looking to sell it. Can anyone give me an idea on what it could be worth It has a front loader, pto, and a grader attachment with a stabilizing wheel-6 cylinder gasoline. Thank you for helping

kelly boyle wrote on Saturday, May 29, 2010 (PDT):

Gil Bacal wrote on Tuesday, May 11, 2010 (PDT):

I just bought a 62 801 with SOS trans everything works fine but the park does not hold when running i adjusted the cable as said in manuel but still does not hold when running it holds when engine is not running ,,any sugjestions be appreciated thanks Gil 417 451-3911

Michael Hartman wrote on Saturday, March 27, 2010 (PDT):

I have a F0rd 3000 w/ Selectomatic. The shifter is missing. I need the whole thing, levers, cables, tube, etc. Can anyone tell me where I can find one

Benny Kiser wrote on Thursday, March 04, 2010 (PST):

can anyone tell why the pto is weak on my 801 ford with sos transmission.transmission pulls great and works great.

BENNY wrote on Tuesday, February 23, 2010 (PST):

HAVE 801 WITH SOS TRANSMISSION. PTO IS WEAK EVERYTHING ELSE WORKS GOOD ANY HELP

Judy Williams wrote on Sunday, October 18, 2009 (PDT):

My husband is refurbishing his Ford 671 select-o-matic. Does anyone know where I can get any decals for this tractor I d like to surprise him for Christmas this year.

Kenny wrote on Friday, August 28, 2009 (PDT):

Hi. I have a tractor just like this one only it says 801 and I need a starter for it. Can anyone help Thanks

GARY wrote on Wednesday, July 29, 2009 (PDT):

My uncle has a ford 801 select-o-speed w/10 forward 2 reverse gears that he was using it just stopped pulling in any gear. Do you have any idea what it could be

Paul Wright wrote on Tuesday, July 07, 2009 (PDT):

I have a Ford 801 Select-O-Speed with afront end loader. I want to know what the current value of this tractor is.

Leon Johnson wrote on Monday, March 09, 2009 (PDT):

I am looking for a tricycle front end for 1950 s Ford tractor unsure of exact model.

DeLee kitchen wrote on Monday, March 02, 2009 (PST):

I am looking for someone else that has a 1961 ford 801 select-o-speed 10 speed trans that a 43hp motor

Christopher Colvin wrote on Wednesday, February 18, 2009 (PST):

I have a 1953 Ford Jubilee. I am in need of the selectospeed shifting cable. I would even buy the housing complete if you would want to sell it that way. I really would like someone to email or call me if they ave info on finding one of these. Yesterdays tractors didn t know where to locate one either. Please call me with the info. Fight for our freedom. God Bless America! Thanks! Christopher Colvin 252 455 0397

terry donakowski wrote on Tuesday, February 17, 2009 (PST):

841 4speed new gears w/ sherman tranny good shape runs added power steering rear pto with loader back blade 4000 firm michigan

Rich Lucy wrote on Thursday, December 04, 2008 (PST):

Need color number for a 961 Ford and photo to restore tractor purchased in need of TLC.

Troy.A.Kirsch wrote on Monday, July 21, 2008 (PDT):

My friend recently bought a Ford 601 select-o-speed at auction. It is in excelent condition he is now the 2nd owner,it was purchaced in 1961 new on a dealers lot as a hold over from 1960 witch is the last year they made this particualer modle.I was wondering does anyone know how many of these were made or sold It seems a rare find,almost everyone to see it says they ve never seen one. Does anyone know what this tractor would be worth to a collecter

Arthur Lee wrote on Sunday, June 29, 2008 (PDT):

I have a 801 powermaster. It set all winter without being ran. When I started it this spring I could not get the cluch to work. It won t kick the tractor out of gear so you can shift. Is there something I can do without tearing into the clutch or transmission. Thanks

ted freilach wrote on Thursday, June 12, 2008 (PDT):

i have a golden demo 971 sos wf ps good running order how much is it worth thanks ted

Dan Nicol wrote on Friday, June 06, 2008 (PDT):

I bought a tractor that was stated as being an 860. However, I can t confirm this because the serial number is gone. I have some questions about what it is and how to tell. Also, I need to know where to find parts for it. I was told it has a bad clutch, but reading your guys comments, I m a little scared about the select-o-speed now. Also, it s a 4-cylinder diesel.

bjr wrote on Thursday, April 03, 2008 (PDT):

I too bought a non running early 4000 diesel, 4 cyl. SOS, Low Center of Gravity and I beleive it s a industrial model as the paint was blue transmission differential and yellow tin work. It had bad torque limit clutch and fuel pump outa time. runs great now. Tire info rears are 12 .4 x 24. I got them set to narrow tread width and use the tractor for tilling smaller gardens the low gear is great for this. I especially like the hydralic clutch PTO, no grinding when putting it into gear. Would like to sell it as I need the cash. Write back here if anyone is interested. I m in Eastern WA. state, south of Spokane, WA. bjr

Bruce wrote on Sunday, March 02, 2008 (PST):

i have one that will only creep forward but reverse works fine, any ideas. B

joey sharp wrote on Sunday, December 02, 2007 (PST):

sorry forgot to say this was a 1974 4000 diesel

Kris Massey wrote on Sunday, October 28, 2007 (PST):

I got a hold of a 1959 881 sos for free!! Guy told me that the trans was bad but everything else works. I got it home did a tune-up on the engine and rebuilt the carb. Engin runs great but like the guy said bad trans, or was it I found the main pressure supply tube to the valve body was broke and the strut to band #1 was in the bottom of the trans. After tig welding the tube back together since they are no longer availble and adjusted the bands I still couldn t get the old beast to move. I could hear all of the servo s working and the three planetary gear sets working as I would shift through the speeds. So I decided to remove the axel coupling access cover and found that the lever on the panel was not in contact with the coupling. So I repaired that and put the tractor back together and was able to drive the tractor out of the garage and around the yard. Thats all I could since I had to put the rest of the tractor back together, but just the trip around the farm was a great ride. Now I have a New Holland tractor as well but having an old vintage tractor for free is awesome!!! I love my 881!!

Jess English wrote on Tuesday, September 25, 2007 (PDT):

Was anyone able t find the decal set for the 671 select-o-matic I came across the hood decal on eBay, but I need the decal for the gear rotator so you can see what gear you are shifting into. Also would love to see some photos of a restored one of these!!! -=jess=-

Gary Baker wrote on Tuesday, September 11, 2007 (PDT):

I have a Ford 881 with a bad trans. I need to find someone to rebuild this trans. for me. I really liked operating this tractor and hope someone can help me. I m afraid to attempt this project alone. I live in Eastern Iowa.

gary wrote on Friday, September 07, 2007 (PDT):

worked ford tractor dealer 1954thru 1999 except 2years out for armyworked on many slecto,s ..when first out many problems at last they had very good but pricede out market,eng who designed it went work jojn deer built powershift for them,

Jerry Lance wrote on Sunday, July 22, 2007 (PDT):

Hi, I purchased a ford 671 s.o.s. It goes in to all 10 speeds but only changes gear range and speed in 5. 5 of them duplicate the other 5. can anyone tell me the problem or tell me where I can get help and information at thank you in advance.

daniel wrote on Monday, July 02, 2007 (PDT):

I have the 681 I Think select-o-speed one reverse ten foward 1 thru 4 works 5 thru 9 dont and 10 works can this be fixed. I called ford an they told me to trash it, but I cant it was my wifes uncle s tractor but the gear thing happen today when I hit a stump with box blade rake. hope you can help me find the part to fix this probllem thhanks.

J. R. Patton wrote on Saturday, June 30, 2007 (PDT):

I have an 841 LP propane tractor that has developed some bearing problems. I need information on where to obtain some parts for the engine, inserts, pistons, rings, rods, etc . I am located in the Texas Panhandle so of they are close it would help. Thanks.

Ray Van Sickle wrote on Tuesday, October 10, 2006 (PDT):

I have a 671 that my father passed on to me. Still in good running condition. The transmission has be rebuilt a couple times. Have to be careful that you get the gear speed selector in the right detent.

Billy La Tulipe wrote on Saturday, August 05, 2006 (PDT):

I have a 1963 SOS model 881 and I am trying to find where I can get the shifter cables and other related tranny parts. I would appreciate the help.

Darrell Reed wrote on Saturday, July 01, 2006 (PDT):

Im looking for someone that knows about the ford 9n, i have a issue with my pto, it does not spin when the tractor is running, the fluid is fresh and the right type. i can engage the lift lever and manually spin the pto and the lift will go up, where do i go from here i am looking to fix it myself if i can Thanks Darrell

Roger Scott wrote on Thursday, June 22, 2006 (PDT):

I just bought a small farm and the owner wants to sell me her 1960 Ford 671 tractor. Any idea what it's worthj. it runs and they use it regularly with a bush hog to cut the field.

wesley wrote on Monday, June 12, 2006 (PDT):

I'm looking to find parts for a 1958 601 select A speed ford tractor. I'm also looking for a select A speed shift cable and the PTO knob. Anyone with info, please reply to the above email address (my daughters) thank you, Wes - June 12, 2006

Bobby wrote on Monday, June 05, 2006 (PDT):

I am looking for the selector assembly that goes on the dash in front of the seat. I purchase my Ford 671 select o speed and it runs perfect, but it is missing the selector to put it into gear. Also, does anyone know of a way to manually put it into gear so i could test the transmission....Any help would be appreciated...

Garry Cottrell wrote on Friday, April 07, 2006 (PDT):

I need a select-o-speed shifter and cable assembly for a 801 Power Master.276-445-5569

dee brazil-dale wrote on Friday, April 07, 2006 (PDT):

We have a 1963 Ford 601 Work Master in good condition with original red paint on hood and iron. Can anyone help us determine the market value? We live near Little Rock AR

ss wrote on Wednesday, February 08, 2006 (PST):

how meney horse power

ss wrote on Wednesday, February 08, 2006 (PST):

how meney horse power

Dan wrote on Wednesday, February 01, 2006 (PST):

I have a 1958 801 with the sos trnsmission and it doesnt want to go into gear sometimes unless im at very low rpm. Sometimes works fine any thoughts...

Erick A. Mogg wrote on Friday, January 20, 2006 (PST):

Young farmer here(17). Just bought me a Ford 971-D. Any Information, parts, etc. for this tractor would be great to hear about. I'm really into my older ford equipment and hope to get my own collection started, thought I'd start early so I can get parts. Some anyhow. Thanks!

ron tullier wrote on Wednesday, November 30, 2005 (PST):

i have a 1964 ford 4000. trying to find a shift cable for the sos transmission. any help would be greatly appreciated. thanks ron!

Gerry L. Sutton wrote on Monday, November 28, 2005 (PST):

I am looking for information on a 981 Selto-Speed that I aquired.

Joe wrote on Saturday, August 20, 2005 (PDT):

I have SOS Diesel. No Idea what year,or model. Where is the Ser.# located? Rear rims are secured to the hubs with locking lugs, If that's what they are called.

Terry Lorenz wrote on Friday, August 05, 2005 (PDT):

Had a 901 Selecto high profile with the California wide front end full adjust in out for 22 inch or wider rows, had to rebuild the engine. Did a complete rebuild from crank and bearings new on up. Parts for motor still on market for the 134 cube motor. SOS tranny worked fine on this one, the gas tank was rusted and crapped out so we bought a reconditioned tank that had a liner blown into it and it was as good as a new tank. This one was red and grey but had gold paint on base almost like primer. It also had a Golden Jubilee emblem in the front of the hood. I heard that was 1953 the anniversary for Ford tractor 50 years out. Great tractor to mow,rake,bale,bushhog,cultivate,ditch,it worked nice with the almost automatic tranny and watched the neighbors getting gears and jamming clutches in shift combat. Traded it in last year restored for a 1997 6200 JD with cab and modern features, it was time for us to move out of the 1950,era. Ron's Equipment in Ft. Collins Colorado has parts for all Fords and knows the ropes on them. Good shop for R&R or restorations too. I really liked the slide out PTO lever on the right side of console/dash smooth in and out no clutching!!!!!!!!!!

gil cox wrote on Tuesday, July 19, 2005 (PDT):

i have a 671 select o speed and i need a wireing diagram

raymond wrote on Sunday, March 27, 2005 (PST):

can someone tell me were i can get decais for my 671sos thank you raymond

Bill Levell wrote on Saturday, February 26, 2005 (PST):

My tractor was bought brand new,by my Dad in 1961 at Nugent Tractor Sales in Lawrenceburg,Indiana The color is all red except the finders and wheels. it's a Ford 671 Select-o-Speed.I have been looking for Decals,( with no luck)COULD YOU PLEASE HELP ME! The Tractor is orgnial.The Decals on the hood has a picture of a Select-O-Speed, with a gold background.Thanks,BILL~Would appreciate any info.

Rocco wrote on Thursday, February 03, 2005 (PST):

I have a sos or som I am not sure? it need to have some work done on the trans... it has the bucket on it. I am looking to sell it if somebody will restore it.. call if intrested 815-693-6874

Alan wrote on Tuesday, January 11, 2005 (PST):

I am looking at purchasing a Select-O-Matic. I do not know the year model and don't know how to tell. Is there a difference between a SOS and Select-O-Matic? Where can I get a Shop Manual for the tractor and transmission? Also Decal Set?

dl wrote on Wednesday, November 03, 2004 (PST):

looking for a 871 select o speed trans.

steve lee wrote on Friday, October 15, 2004 (PDT):

we have a 1959 gold 871 ford sos, would like information on this tractor. also any help as to it's value, thanks ahead of time steve

RAYMOND R wrote on Tuesday, October 12, 2004 (PDT):

GETTING BACK TO MY FORD 671 SOS, I FORGOT TO MENTION A COUPLE OF THINGS. THE TRACTOR HAD SAT FOR 5 YEARS WHEN I PURCHASED IT, AND ALL I DID WAS PURCHASED A NEW BATTERY AND CLEANED THE POINTS AND IT FIRED RIGHT UP AND RUNS BEAUTIFUL. THE FOLLOWING DAY I BRUSH HOGGED 5 ACRES OF PASTURE PULLED OUT MANY MAPLE TREE STUMPS. AND AS I STATED BEFORE I WOULD NEVER GET RID OF IT, AND FOR ANYBODY THAT NEEDS PARTS FOR THE 671 SERIES SHOULD CONTACT MEDINA TRACTOR SUPPLY IN MEDINA, OHIO. ALSO, MY NEIGHBOR WHO IS STRICTLY JOHN DEERE TOLD ME THAT I GOT ONE HELL OF A TRACTOR.

RAYMOND R wrote on Tuesday, October 12, 2004 (PDT):

I JUST GOT A 671 SOS AND I LOVE IT IT IS SO MUCH BETTER THEN MY 8N FOR BRUSH HOGGING I WILL NEVER GET RID OF IT

Cody Barlow wrote on Thursday, August 12, 2004 (PDT):

Does anyone have any suggestions on getting and mounting a front end loader on a 1962 Ford 901 D with dual front adjustable wheels? I cannot figure out how to mount the pump as most I have seen drive off of the Crankshaft. Impossible with the pedestal.

frank smith wrote on Wednesday, June 23, 2004 (PDT):

i bought a ford 841 powermaster. i have never heard of this tractor before. i am looking for an owners manual and can't seem to find on on line anywhere. if anyone knows anything about this tractor please contact me at frankgsmith at aol.com thanks

Bob Plugge wrote on Monday, June 07, 2004 (PDT):

I have a sos an need to find the cone that goes over the shifter. If you know where I could find this item, please reply. THANKS

Dennis Korbel wrote on Friday, May 21, 2004 (PDT):

I have a(mid 60"s) 4000 with sos trans. It seems to work just fine, but there seems to be a high pitched howling coming out of the gear box, or rear end area. The fluids are fine and etc. There is no problem with over heating. I was hoping someone could give me some advise on this. Thanks, dk

Kim Benson wrote on Wednesday, May 19, 2004 (PDT):

I have an 881 SOS and I need a new/used transmission pump. Can anyone out there tell me where I can get one, I can't seem to find one. I'm almost considering buying a 881 parts tractor, does anyone know where one is? These aren't easy to find either. Another question,, Will the transmission pump from a 671 or from another SOS work or fit in my 881? Thanks KB

Larry Polley wrote on Tuesday, May 11, 2004 (PDT):

My dad has a 1964 Ford 671 Series that he has used daily for 30+ years. The selcto speed has just began to act up. We have been looking for a transmission manual. There doesn't seem to be anyone in this neck of the woods that wants to touch it. Any suggestions regarding where one might obtain a manual?

Ken Kallam wrote on Monday, April 12, 2004 (PDT):

I have used SOS tractors for a long time, they are very strong and tough. I have a l973 4000 that has several advantages over the older SOS tractors and would consider selling. have just gone through the transmission. Excellent tractors to bale hay and bush hog with. enjoy their use.

steve evans wrote on Sunday, March 21, 2004 (PST):

I have a 901 with loader in working condition,what would it be worth?

george curran wrote on Wednesday, March 03, 2004 (PST):

nate watson i see your note sept. 25/2002 re 871 c/w S.O.S. tranny & you were thinking of converting it to a standerd tranny etc. did you get any satisfaction ? i'm the owner of a 6000 commander 1964 and i would to do something along the same lines. thanks for any help George.

Robert Montgomery wrote on Saturday, February 21, 2004 (PST):

Iam presently looking at a 871 gas tractor. It needs a shift cable,if anyone knows where I can find one .I am interested in other parts also. thanks rob.

Jack L Hammonds wrote on Wednesday, January 14, 2004 (PST):

I have a 801 Ford select-O-Matic with a ford 722 loader on it. I am hard on a tractor and let me tell you this tranny stands up to the hard labor I put it through. Just rebuilt engine but have no problem with the transmission.

Richard Lee wrote on Thursday, January 08, 2004 (PST):

I am very interested in purchasing a ford tractor for our new property in Colorado. Would like to have 8n, 9n or 600 with bucket and gannon. Dont know much more about them and would like more information on these. Thanks.Rl.

Karen Reynolds wrote on Wednesday, December 17, 2003 (PST):

We have a Ford 671 sos that we are interested in selling. Where could one try to sell it on the web and what is it worth? I do not know the year and can send pictures.

Kerry Wagner wrote on Sunday, November 23, 2003 (PST):

I just bought an 841 with the ELENCO 4wd setup and a Sherman 12-speed transmission. It also has a Ford loader on it. I'm gonna restore it. Anybody know where I can get info on the ELENCO front end and the Sherman transmission? Thanks.

Alan Morse wrote on Sunday, November 02, 2003 (PST):

I once owned a 1958 871 Select-O-Speed. Great for bushhogging because it would crawl slowly in tough going. It also had the inching pedal which really let it creep along. In the winter it was tough to get it to move if it had not been inside and warm.

Bill Stocks wrote on Thursday, September 11, 2003 (PDT):

We have a 66 model 4000 with sos that when put into 3rd forth and fifth will stall the engine.We received it from uncle who retired from farming and are not very familier with it.Anyome have any suggestions?

jeff bartlett wrote on Saturday, August 30, 2003 (PDT):

i have my dads 60 model 601 sos diesel. used it everyday with his company from 73 to 79, employee bust trans housing, it sit for about 8 yrs, could find no one to work on it, converted it to a 4 speed works fine now, ask me for more details on the swap out of sos for a 4 speed

Tom Pilotti wrote on Tuesday, August 19, 2003 (PDT):

I need the shifter control console/assembly that mounts on the column directly in front of the seat for my 1963 Select-O-Matic. If you have one, pls e-mail me.

Brandon wrote on Monday, July 14, 2003 (PDT):

I have an 881 SOS diesel tractor, have a few implements with it. We havent done much messing with it yet, other than seeing if the engine will turn over (which it does) Im not sure what year it is, it was left at the land we purchased recently as they didnt want to haul it with them. I was wondering if anyone knew what this tractor is worth as it sits vs. restored..? We may just get rid of it since we bought a new tractor, but I dont know what to ask for it. If anyone knows a price range or a place to post "tractors for sale" let me know.

Eric Burger wrote on Monday, June 23, 2003 (PDT):

Hello I was wondering if you could help me out. I have a Ford 881 Select O Speed Tractor with various attachments. I'm looking to sell this item, but know nothing about it. If you could please tell me where I could find information about it so that I could describe it accurately, I would appreciate it. Also I'm planning to sell it on EBay unless someone else has a better idea.

Briam W. Berggren wrote on Thursday, May 08, 2003 (PDT):

Nice! Very Very Nice!

Dave Curtician wrote on Wednesday, April 16, 2003 (PDT):

I have a 1964 4000 with a worn out trany input shaft and tork limiting clutch. Any suggestions about repairs ?

Bob Sorrels wrote on Friday, April 04, 2003 (PST):

I own a Gold 871 that caught fire last year. Up until then ithad been a very reliable tractor, mostly used for gathering fire wood in steep terain. I am looking for a gas tank as mine expanded because of the fire and no longer fits under the hood.

Greg Moul wrote on Thursday, January 30, 2003 (PST):

I have an 1959 871 with a 3 pt hitch grader blade to push snow.. It works great.. I see on the picture above that theirs a port in the front below the radiator.. Is that for a hand crank?? My 871 doesn't have that port..

paul stephenson wrote on Monday, December 02, 2002 (PST):

Can anyone out there help me find a Ford 671 with a Elenco front assist conversion? thank you

carl simpson wrote on Sunday, November 24, 2002 (PST):

my sister has ford selectospeed tractor , approx.year is mid to late 50s. the clutch is not working, I can not figure out how to remove the cover with the two cable that run in to the top of the transmission cover. I have called several tractor mechanics, but they keep telling me I should bring the tractor in to them for repairs. my sister can not afford to take the tractor to a mechanic because of the cost. My question is, can I as a beginner repair this transmission. How do I get the cover off without making the problem worse? Any information or help would greatly appreciated. Thank you. Carl in Michigan

nate watson wrote on Wednesday, September 25, 2002 (PDT):

I am currently looking at a ford 871 with SOS transmission, the trandmission has some problems and if I purchase it I would like to convert it over to a standard transmission. What tractor model would have a compatable transmission and what other parts if any would I need in order to convert it over?

TOM GARRETT wrote on Thursday, September 05, 2002 (PDT):

IAM LOOKING A SENDING UNIT FOR A 1950 601 WORK MASTER {FORD}ANY OUT THERE.

TOM GARRETT wrote on Thursday, September 05, 2002 (PDT):

IAM LOOKING A SENDING UNIT FOR A 1950 601 WORK MASTER {FORD}ANY OUT THERE.

Ed.S wrote on Wednesday, August 28, 2002 (PDT):

To ID your Ford Tractor 1953 to 1962,try Yahoo search,type in, THE VINTAGE FORD TRACTOR RESOURCE,paint schemes,SOS troubleshooting,emblems etc.can be found on this site.

Cameron wrote on Friday, August 16, 2002 (PDT):

I picked up a 1958 971 SOS about a year ago to level and pull stumps on the homestead here in Alaska. Nice tractor with a lot more power than a 8N or Jubilee, actualy a little over kill on the power, have snapped several lift arms. I took out several dozen 12"-30" birch/spruce stumps with a sub-soiler and box blade. As far as tranny problems; alot of times it's only the selector handle out of adjustment and not engageing intended "notch" correctly. I have to agree with most of the other comments; SOS's make for great collectibles but if you are really going to work it, play it safe and stick with the gears.

john conlon wrote on Saturday, June 15, 2002 (PDT):

I have 1961 881 ford sos tractor had tranny rebuilt about25 years ago no problems since.

Doug wrote on Monday, June 10, 2002 (PDT):

My grandfather has a FOrd 600 series tractor he's restoring and was wandering what the correct date of manufsacture was the srial numbers read 114902. He thinks it is a 660 since that is what is stamped above these numbers but ha was told that it was a '62 but that doesn't jive with the bio on this tractor. another site said it was a 1956 and was just getting a second opinion. Any info would help thanks

jw- wrote on Monday, May 27, 2002 (PDT):

I have a 57 871 Select-O-Speed. I have never had any problems with it until recently. I was working on a little wetland project near my home. I was using a 3pt bucket to build a little island for ducks to nest(my cats put them out of business last year). Anyway I was doing a lot of backing up and pulling dirt up to form an island. I don't know why but the shifting pattern changed. Displayed park is now 1, r2 - 2, r1 - 3, n - 4, etc. displayed 8 is now nuetral and 9 and 10 are the reverses. If anyone has any idea what went wrong I would appreciate some advise.

earle wrote on Sunday, September 02, 2001 (PDT):

I have a 53thur 59 Ford 671 needs engine can someone tell me where i might be able to purchase one quite sure its a 134cu in. everything else on her is is good shape. Lives in South Carolina

TRJ wrote on Thursday, August 16, 2001 (PDT):

I have a '53 Jubilee with a Select-O-Speed. It's been in my family for 30 years and I've never had a problem with the transmission.

louis smith wrote on Monday, August 06, 2001 (PDT):

I have a 1959 Ford Deisel select-o-matic with transmission problems. I pulled the handle for the PTO to engage and nothing happened. I then put it in gear, but still nothing. It starts fine but will not do anything else. The local Ford dealer will not give me an estimate on. Anyone have any suggestions. thanks

Doug Collins wrote on Tuesday, July 17, 2001 (PDT):

I have a selecto-speed 971 Trans is no good would be willing to sell to someone that needs parts gas engine everything else works i live in Dayton, ohio area e-mail me if interested

robert lamb wrote on Monday, June 11, 2001 (PDT):

my girlfriend's brother has a 971 speedomatic tricycle front end. don't know what year, it is runs real well

no matter wrote on Thursday, May 10, 2001 (PDT):

Actually, we have a 901 seolect-o-speed tricycle front end, tractor, so the "7" theory is wrong!!

Charles R. Colen, Jr. wrote on Saturday, May 05, 2001 (PDT):

I need some help! I have a Ford 671 Select O Speed and I need the entire back end for gears. Does anyone have these parts and are willing to sell them? If so please send information with a price. Thanks!

Doug Gilliam wrote on Tuesday, April 17, 2001 (PDT):

need help, have recently purchased a 4000 select-o-matic not working in all speeds, or if it is tiltd slighly to one side it seems to quit .pto runs all the time, looks great, diesel engine runs great, but no one in these parts seems to think its worth fixing or will offer any help.

burt wrote on Sunday, April 01, 2001 (PDT):

restoring 1959 gold demo 871D power steering help

Johan Nel wrote on Tuesday, March 20, 2001 (PST):

I have a Ford 3000 Super Dexta SOS (+/- 1967). The clutch peddal broke off. How do I get the rest of the "pin" out that goes into the housing? Anny help would be appreciated. Johan Nel

Gerry Loucks wrote on Sunday, December 10, 2000 (PST):

We know very little about our 871 Ford tractor with original gold paint. We got it from the original owner who said he bought it in 1959 and that each dealer only got one as a promotion for the selectospeed transmission. It has under 1000 hours and is in very good condition. we would like to know more, might think of selling.

Greg Moseley wrote on Tuesday, November 28, 2000 (PST):

I have aquired a 671 sos diesel, has the original tach with 4993 hrs. It runs the best, The farmer I bought it from said he only used it to pull tobacca trailers. Would like to sell if anyone interested. All orignal.

David Hollister wrote on Saturday, November 11, 2000 (PST):

Was looking for manuals for an 811 that I'm ready to buy. As a special utility does that mean they (the 811's) always came with the loader and backhoe as this one has? Where would I look on the backhoe and the loader for ID so I could try to get the correct manualsvfor these? Thanks for any help.

Bob Sobolewski wrote on Wednesday, September 13, 2000 (PDT):

I am iterested in older ford tractors many the commander series. Any information regarding these tractor would be helpful. I am also looking for one to buy any of these for sale out there.

Jeff wrote on Friday, September 01, 2000 (PDT):

I have an 871 SOS desiel. I've owned it 5 years with no problems. It has a "Superior" loader mounted on it. Great tractor for loader work. I'm looking for good place to get parts (like the proofmeter). I'm unsure of the year. The center of the hood and frame are red. The rest is gray.

John Hague wrote on Monday, July 24, 2000 (PDT):

I just bought this old Ford tractor that had been sitting for 1 to 2 years. I've been searching the internet for the last couple of days trying to identify it. It doesn't have serial numbers by the starter where everyone says they should be. A picture on this website look very similar to my tractor and it appears to be a 671. It has the sos xmsn and one rear pto. All the heavy iron is blue but by scratching the blue, it has red underneath. Can anyone suggest ways to confirm it's identity. I want to buy manuals for it.

Bob Meinholz wrote on Saturday, July 22, 2000 (PDT):

Kurt the answer to your question on the colors is; The front rims are the same color as the fenders and the rear center hubs as well. The outer rim in the rear is painted silver (the rims originally were galvanized).

Carl Sabo wrote on Sunday, July 02, 2000 (PDT):

I bought my tractor three years ago and have found it to be pretty reliable. I think the select-o-speed has been great. I, too, find that until the fluid warms up the tractor won't lock in park. Is it some thing to worry about?

Herb Wheeler wrote on Monday, June 05, 2000 (PDT):

I've got a GOLD 871 tractor that is a breeze to use. My mother-in-law has an NAA and it won't go slow enough in 1st to do any heavy brushhogging. I hear alot of bad about the SOS tranny, but I think it's worth a few problems being I'm not a farmer(my Dad was!)ENJOY!

Kurt Richardson wrote on Saturday, June 03, 2000 (PDT):

I recently aquired my Grandads 1958 Ford 801 sos. It has all original paint. Has always been stored inside. It has red frame and engine, red and grey front sheet metal with grey wheel fenders. QUESTION; The front and rear rims are some what rusted, no original color remains. Does any one know what color the rims should be, or better yet, are there any pictures out there? I have been surching and have come up empty. Thanks in advance. jambo. Pella, iowa.

Bill Oakes wrote on Thursday, June 01, 2000 (PDT):

I have a 1960 681; SOS with dual PTO speeds. I have been driving this one since the day it was new. The hood and iron are red, for sure. Love my Ford!!

Marvin Asche Raymond,mn. 1090 160 SE 56282 wrote on Friday, March 10, 2000 (PST):

I have a 641 ford tractor and has the red hood that was not painted ever. I love it but got to sell it because I had A hartatack,NO INSURANSE. need money.

John Harlan wrote on Friday, February 04, 2000 (PST):

1963 Ford 901 Selecto-O-Speed, Am considering selling original running tractor with tricycle front end Ford loader. All operational and original. I too like the select-o-speed,it has had alot of bad press but my experience has been positive.

Joe G wrote on Tuesday, January 18, 2000 (PST):

Bill, there is a lot of info on the sos x-mission available. Take your time and look at it in sections not as a whole when repairing. It's no more difficult than a regular automotive automatic. Don't forget, you've got to be a perfectionist to work on any automatic.

Bill wrote on Monday, January 03, 2000 (PST):

I have a ford 4000 SOS 1970 Model and the tractor works good except it goes foward when the inching pedal is depressed or in neutral. I have not found out why the pressure all check good. People have told me this is normal for these transmission, I find that hard to believe because if this tractor did this when new Ford would have never sold any. I make it hard to hook up implements. Any information out there or do I have to live with this problem. The tractor shifts through all gears and seems to work fine otherwise.

HENRY T. MARTINEZ wrote on Saturday, November 27, 1999 (PST):

MY BROTHER HAS A 1964 4000WITH SELECT-O-SPEED HE GOT IT CHEAP PREVIOS OWNER DID NOT WANT TO SPEND TIME FOR REPAIR IT TOOK US ONE SERVICE TWO PRESSUREGAUGES 40.00OF PARTS IT RUNS GREAT.BEST THING FOR MOWING &BALING HAY

Ken Ray wrote on Sunday, August 08, 1999 (PDT):

With regard to the Select-o-Speed, I too have found it very nice. I have a 1962 4000 row crop with the SOS, and enjoy the ease of changing speed. With respect to the paint scheme, my Dad had a 601 Workmaster, and I agree it was a red sheetmetal/red engine. All other 601 references are the same that I have seen. As to other colors beneath the original, I have found that on my 4000. It has a early 1962 serial #, and after I recently took mine down to bare metal to restore, I saw red beneath the blue. Given the resemblance and inter-changablity of early 4000 parts with the 901, I suspect that leftover 901 parts were used in the first production runs for the 4000.

Larry Dotson wrote on Tuesday, July 20, 1999 (PDT):

I recently purchased a 1959 Ford 671 select-O-speed diesel. This tractor had been painted blue and passed off as a 2000. In my investigation, I have concluded that it is a 671. I am still looking for proof of this. When I opened the hood, I find the inside of all body panels were originally red. When the seat was removed, it was red under it. There is one odd thing though. The control arms for the front axle are gold under a coat of red. Also the rear rims (outer rim only) were first painted gold. I have not found the gold anywhere else. Does anyone know if this is correct, or for what model? The serial number seems to have been eaten off by battery acid. I was told that it was on the left side. Any help would be appreciated. Larry Dotson

David Bradley wrote on Tuesday, July 06, 1999 (PDT):

The 601 and 701 series tractors all had red hoods with gray grills. Correct me if I'm wrong.

SHOP FOR PARTS	SHOP FOR MANUALS

Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We've kept the same low rate for six years. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home | Forums

Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others.

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within these website pages are the property of their respective trademark holders. None of these trademark holders are affiliated with TractorShed.com, our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Antique Ford Tractor: Ford 671 Select-O-Speed

Comments on this Tractor

Use This Form to Add Your Own Comments or Questions